In this article, I have tried to cover some of the special flanges such as Orifice flange, long weld neck flange, reducing and expanding flanges, and flangeolet that used in piping and equipment. Special flanges are not as common as regular flanges. They are used to serve some specific function within the piping system.

Long Weld Neck Flange

As the name suggests, Longneck flange has a long neck than a regular weld neck flange. Other than the neck, all the dimensions are the same as the regular flanges.  You can see the difference in the image. It is used as a nozzle in the pressure vessel and heat exchanger.

long weld neck flange
Long weld neck flange welding
Pipe Flange welding

Here, in these images, you can see that Longneck has two advantages over the normal pipe to flange connection. First, it does not require pipe piece and second, it eliminates a but weld between pipe and flange that required in case of conventional nozzle connection.

These types of flanges are normally used in high pressure and temperature application. It is costly but gives high reliability and reduces fabrication efforts as compared to a normal pipe to flange type nozzle.

ASME B16.5 covers the dimensions of the long weld neck flanges.

 

Orifice Flange

Orifice Flanges are used with an orifice flow meter that is why it called orifice flanges. The purpose of the orifice meter is to measure the flow rate of either liquids or gasses that pass through the pipe.

These flanges are always used in a set of two. In this image, you can see the complete set of items that used with orifice flange.

Two flanges, Orifice Plate, Gaskets, Pressure taps, and Jack screw hole with two jackscrews. I will explain each of these.

orifice flange

Image Source: www.flowmfg.com

Orifice flanges are available from Class #300 to Class #2500. Class #300 flanges are available in threaded, slip-on, and weld neck end types. Whereas, Class# 600 and above flanges are available in only weld neck type end connection.  Dimensions of these flanges are covered in ASME B16.36.

The orifice plate is a specially designed plate with a hole at the center that creates a pressure drop to measure the flow rate. Please note that the orifice plate is not interchangeable. It means you cannot use an orifice plate of water line into the hydrocarbon line.

The size of the hole and the angle, as shown in the image, are specifically designed for the service.

orifice-plate

Next is the gasket. There are only two types of flange faces are available in orifice flange. Raised face and RTJ face. Therefore, only spiral wound and RTJ gaskets are used that too in the set of two for each side of the orifice.

These jack screws are drilled on the flange circle centreline at 90 degrees to the tapped hole and used to facilitate separating the flanges for inspection or replacement of the Orifice Plate and gaskets.

orifice flange jack screw

Pairs of pressure “Tappings”, as highlighted in the image, are machined into the orifice flange. Note that these holes are directly opposite each other.

Tap holes are either tapped ½” NPT or ½” NPS socket connection. A one-tap hole from each flange is used to connect instruments with the help of a tube that allows liquid or gas to reach the instrument. You can see this in the image. The other hole is sealed with a plug.

Orifice Flange Installation

Orifice flanges are installed in a straight run of pipe in order to avoid turbulence at the plate. As a rule of thumb, an orifice flange has ten diameters of straight pipe upstream and five diameters of straight pipe downstream. In general pressure taps kept at the same elevation to each other.

orifice flange installation

Image Source: idSolutions

Orifice flanges are available in Class# 300, 600, 900, 1500, and 2500-pound rating, and the Dimensions are covered in ASME B16.36. Images show the installation setup of an orifice flow meter.

Reducing Flange

Reducing flange is used in place of a standard flange to allow for a change in pipe size. This flange eliminates the need for a standard reducer in piping.  The flange consists of one specified diameter with a smaller diameter bore size.

Except for the bore and hub dimensions, a reducing flange has dimensions of the standard pipe flanges size and is considered an economical means to make a pipe size transition.

These flanges are available in weld neck, slip-on, and threaded end types. Reducing flanges are an economical way to make transitions between pipes of different sizes, however, due to high-pressure loss, they are rarely used in piping. ASME B16.5 covers the dimensions of reducing flanges.

reducing flange

Image source: www.msmmfg.com

Expander Flange

It is similar to a weld neck flange but increases the size of the pipe to the first or second larger size. It is an alternative to using reducer and weld neck flange. Useful for connecting to valves, compressors, and pumps.

These flanges are specially designed. Dimensions of the weld neck are in line with the connecting pipe, other dimensions are in accord with standard ASME B16.5 flanges.

expander flange

Image source: www.msmmfg.com

Flangeolet / Weldoflange / Nippoflange

Flangeolet is a combination of olet (mainly weldolet or nipple) and flange. As you can see in the image that hub length is longer like long neck weld flange. It is a 90 Degree branch connection use for high-pressure piping.

It reduces the two weld joints than the traditional Olet + Pipe + Flange connection and one weld joint in case of Olet + Flange connection. You can see the image of the flangeolet branch.

flangeolet

Don’t Forget to Subscribe

Thank You for subscribing to Hardhat Engineer. Your Ebook will Open in New Tab

Use Your Genuine Email to get Updates on this Ebook in the Future.